77 lines
43 KiB
JSON
77 lines
43 KiB
JSON
[
|
||
{
|
||
"id": 1,
|
||
"chunk": "# Bio-inspired antifogging PDMS coupled micropillared superhydrophobic arrays and $\\mathsf{S i O}_{2}$ coatings† \n\nZhiwu Han, $\\textcircled{1}$ a Xiaoming Feng,a Zhibin Jiao,a Ze Wang,a Junqiu Zhang,ab Jie Zhao, a Shichao Niu $\\textcircled{1}$ \\*a and Luquan Rena \n\nIn this work, inspired by some typical creatures from nature with superhydrophobic surfaces, a bio-inspired antifogging PDMS is designed and fabricated successfully using UV lithography and a template method. First, we fabricated an SU-8 layer with a bio-inspired micro-pillared array (MPA) using traditional UV lithography. Then, it was used as a template to fabricate a PDMS film (PF). After that, it was chemically modified with $\\mathsf{S i O}_{2}$ coatings. It was found that the PF coupled with sprayed $\\mathsf{S i O}_{2}$ coatings and a MPA have a higher water contact angle (CA) of $158^{\\circ}$ and a lower contact angle hysteresis (CAH) of less than $2^{\\circ}$ . Water drops can be separated from this bio-inspired PDMS surface within $86.8~\\mathsf{m s}$ More importantly, this film’s antifogging property is superior, with a recovery time of less than $\\begin{array}{r}{13\\ \\mathsf{s},}\\end{array}$ which is significantly superior to that of the flat PF and the PF with the MPA. Afterwards, FTIR was applied to analyse the surface chemistry features and suggested that the bio-inspired PF has extremely low surface tension. So, it can be confirmed that an excellent superhydrophobic antifogging property has been achieved on the surface of the PF. Meanwhile, the microscopic and macroscopic dynamic movement behaviour of the fog drops was further observed. Then, the underlying antifogging mechanism was also revealed. These properties mainly benefit from the coupling effect of intermolecular attraction of droplets, chemical compositions (nanometre roughness $\\mathsf{S i O}_{2})$ and the physical structures (MPA). The investigations offer a promising way to handily design and fabricate multiscale hierarchical structures on polymers and other materials. More importantly, these findings suggest great potential value for specific antifogging applications in display devices, transport, agricultural greenhouses, food packaging and solar products, especially in continuous harsh fogging conditions.",
|
||
"category": " Results and discussion"
|
||
},
|
||
{
|
||
"id": 2,
|
||
"chunk": "# 1. Introduction \n\nFog formation and accumulation on the surfaces of equipment, such as eyeglasses, windshields, goggles, lenses and display devices in analytical and medical instruments, are known to cause serious economic and safety problems.1–3 The fundamental principle of antifogging materials is to regulate the interaction between water drops and the solid surface via surface chemical composition as well as the rough features’ size and geometry to ensure appropriate wettability.4,5 Antifogging surfaces with hydrophilic or even superhydrophilic wetting behaviour have drawn wide attention due to their ability to signicantly reduce light scattering by only allowing fog droplets to condensate in a lm-like form.6–9 However, under harsh fogging conditions, these surfaces may exhibit frost formation or excess and inhomogeneous water condensation, which would cause irreversible catastrophic results, such as ceasing the operation, impairing the efficiency or even paralyzing the entire system, especially when considering applications in aircras, wind turbines, high-voltage power transmission, telecommunications equipment and heat exchangers.1 Superhydrophobic-induced antifogging behaviour not only can improve the evaporation rate of fog because of its high CA to the tiny water droplets,10 but can also induce tiny condensed droplets to merge with each other easily and then shed from the surface. This prevents moisture or microscale fog droplets from nucleating on a surface and so that the surface remains dry.11–13 \n\nBio-inspired micro-/nanopatterned structures combined with a variety of material substrates can improve the water repellency performance, even leading to the enhancement of the antifogging ability.14–17 Compared with these materials, polymer materials have lots of peculiar attributes, such as low cost, good deformability and ease of fabrication and so they have broader application prospects.18,19 Polydimethylsiloxane (PDMS) is typical example of these materials.20,21 PDMS is inherently water repellent and one of the frequently-used surface modiers to create superhydrophobic surfaces.22 Introducing different surface textures such as microwell arrays,23 femtosecond parallel arrays24 or other 3D pattern dependent structures25 into PDMS surfaces can create some chemistry/ topography-combined superhydrophobic surfaces. However, a plausible issue has recently arisen. Superhydrophobicity is not the only criteria for generating high-performance antifogging or even anti-ice surfaces.26 Besides, most of the methods are not scalable for industrial level. In fact, PDMS microscale pillar arrays can achieve higher CAs over $150^{\\circ}$ without further coatings or treatment steps,27,28 but their antifogging ability is not obvious because of the good adhesion to droplets of PDMS itself. Some investigations on antifogging function involving PDMS have been reported, for example, the involved PDMS layer was treated with $\\mathbf{O}_{2}$ plasma to convert into highly porous silica lms,29 or as a “seed layer” by photochemical oxidation,30 the common purpose was to result in a superhydrophilic antifogging layer. In addition, Zheng and co-workers11 rst designed a composite micro/nanostructure surface using a polyvinylidene diuoride polymer as the substrate, showing excellent antifogging and icing-delay properties. Next they presented a series of surfaces combined with nanohairs and micropillar arrays using PDMS as a negative replica and then epoxy as the substrate, demonstrating the excellent anti-icing abilities of the surface.15 This provides the inspiration for our work as, to the best of our knowledge, the antifogging performance using PDMS directly as the substrate has rarely been characterized in detail. \n\nHerein, we designed the surface asperities to take the form of a regular micro-pillared array (MPA) using a PDMS lm (PF) in combination with a silicon dioxide $\\left(\\mathrm{SiO}_{2}\\right)$ modication. In this fabrication, an SU-8 mold of negative well arrays was obtained using traditional UV lithography, then a so replication method was adopted to obtain a PF with a MPA as the substrate. Subsequent $\\mathrm{SiO}_{2}$ nanometer coatings were sprayed on the surface of the PF with the MPA. Depositing a layer of $\\mathrm{SiO}_{2}$ on the surface of the PF with the MPA using a spray coating technique makes PDMS with a superhydrophobic antifogging property. The dimensional uniformity and quality of the as-prepared PF was characterized with the help of eld emission scanning electronic microscopy (FESEM). Fourier transform infrared spectroscopy (FTIR) results indicated that both the functional groups of $\\mathbf{-CH}_{2}$ and $\\mathbf{-CH}_{3}$ existed on the surfaces of the bioinspired PF samples, which not only increases their hydrophobicity dramatically, but also decreases their water adhesion performance. So, the superhydrophobic antifogging performance of the bio-inspired PF is ensured. Meanwhile, a set of optimized models were generated to illustrate the fabrication process. Moreover, the nal antifogging behaviors were also revealed. The antifogging properties of the PF were characterized experimentally using a spray simulation system and an optical CA measuring device. The time-lapse transmittance measurements demonstrated that the as-prepared PF possessed a superior fogging recovery property because it can reach a plateau in far less time $(<13\\ s)$ . It also suggested a reliable optical performance in practical outdoor conditions. Furthermore, the dynamic antifogging behaviors of the PF coupled with $\\mathrm{SiO}_{2}$ coatings and the MPA were observed carefully, verifying that the MPA can get dry and the fog drops can drop from the asmodied PF. It was conrmed that PF coupled with sprayed $\\mathrm{SiO}_{2}$ coatings and the MPA possesses excellent superhydrophobicity and antifogging behaviors.",
|
||
"category": " Introduction"
|
||
},
|
||
{
|
||
"id": 3,
|
||
"chunk": "# 2. Results and discussion \n\nIn this work, we designed a matrix of geometries made of periodic structures on a PDMS substrate. The overall process of preparation is shown in Fig. 1. Briey, a clean glass slide was spin-coated with a negative photoresist SU-8, the spinning speed determined the thickness of the SU-8 coating; a photomask containing the circle-shaped arrays was utilized in traditional UV lithography; the unexposed SU-8 was ushed off in the developer, leaving the circular micro-hole arrays standing on the glass slide; a mixture of the PDMS pre-polymer and curing agent in a $10:1$ mixture (by weight) was degassed using a vacuum chamber and carefully poured onto the SU-8 masters; aer curing at $80~^{\\circ}\\mathbf{C}$ for $^{\\textrm{1h}}$ , the PDMS sample was gently peeled from the mold; the commercial $\\mathrm{SiO}_{2}$ coating agent was sprayed on top of the as-prepared PDMS. As illustrated in Fig. 2a, the side length of the pillar $(L)$ is about $5~{\\upmu\\mathrm{m}}$ , the pitch between neighboring pillars $(P)$ is about $7.5~{\\upmu\\mathrm{m}}$ and the nominal height of the pillar $(H)$ is about $6\\upmu\\mathrm{m}$ . The quality and uniformity of the pillars were inspected using FESEM. The FESEM sample was titled at $45^{\\circ}$ to reveal the actual structures. Fig. 2b shows the PDMS coating has a negligible effect on the global structure of the MPA, though the individual micro-pillar was coated with nanoscale $\\mathrm{SiO}_{2}$ (Fig. 2c). The FESEM results indicate that the asprepared PF possessed a rough surface and contained many bumps. \n\n \nFig. 1 The fabrication process of the bio-inspired PDMS coupled with sprayed $\\mathsf{S i O}_{2}$ coatings and the MPA. (a) A clean glass slide was spincoated with a negative photoresist SU-8. (b) A photomask containing the circle-shaped arrays was utilized during the process of UV lithography. (c) With the circular micro-hole arrays (CMHAs) standing on the glass slide, PDMS was carefully poured onto the SU-8 masters and then gently peeled from the mold. (d) The commercial $\\mathsf{S i O}_{2}$ coating agent was sprayed on top of the MPA surface. \n\n \nFig. 2 (a) The top view (left) and side view (right) of the MPA. This pattern was repeated periodically across the PDMS surface. (b) The FESEM image of the fabricated $\\mathsf{S i O}_{2}$ -sprayed MPA under low-magnification, demonstrating that the coated PDMS has a negligible effect on the global structure of the MPA. (c) The $\\mathsf{X}$ -ray diffraction (XRD) spectrum of the coating and high-magnification FESEM image shows the nanoscale $\\mathsf{S i O}_{2}$ (insert). \n\nThe wettability properties of the at PF, PF with the MPA and PF coupled with sprayed $\\mathrm{SiO}_{2}$ coatings and the MPA were examined separately via an optical CA measuring device based on a sessile drop technique. An average of ve measurements on each sample is effective. Fig. 3 shows the water CA of the three PFs was linearly increased and the hydrophobicity of at PF and PF with the MPA was compared, exhibiting water CAs of $114^{\\circ}$ and $133^{\\circ}$ , respectively. The PF coupled with sprayed $\\mathrm{SiO}_{2}$ coatings and the MPA was found to be superhydrophobic, showing an average water CA of $158^{\\circ}$ . This indicated that the change in surface structure results from the MPA signicantly increasing the water CA, rendering the surface superhydrophobic. The superhydrophobic property was elucidated using the Cassie–Baxter model,31 suggesting that the microstructure on a low-surface-energy material signicantly improved the superhydrophobicity of the surface. \n\n \nFig. 3 CA and CAH measurements of three PF surfaces. The error bars denote standard deviations, which were obtained from distinct measurements on the three different PFs and at least at five different locations on each. \n\nThe effective CA of the droplets can be regulated by the equation cos $\\theta_{\\mathrm{c}}=f_{\\mathrm{s}}$ cos $\\theta_{\\mathrm{{s}}}+f_{\\mathrm{{v}}}$ cos $\\theta_{\\mathrm{v}},$ where $\\theta_{\\mathrm{{s}}}$ and $\\theta_{\\mathrm{v}}$ are the CA of the liquid contacting with solid and vapor parts and $f_{s}$ and $f_{\\mathrm{v}}$ are the area fractions of the solid and vapor on the surface. If rough structures on a surface can generate entrapped air pockets, in such circumstance, $f_{\\mathrm{s}}+f_{\\mathrm{v}}=1$ and $\\theta_{\\mathrm{v}}=180^{\\circ}$ . $\\theta_{\\mathrm{c}}$ can be calculated by the following equation, \n\n$$\n\\cos\\theta_{\\mathrm{c}}=f_{\\mathrm{s}}(\\cos\\theta_{\\mathrm{s}}+1)-1\n$$ \n\nIn addition, a superhydrophobic surface with low adhesion to droplets is a crucial index of antifogging materials. It is found that the water adhesion on both the at PF and the PF with the MPA was high. Therefore, our starting surface was hydrophobic with high adhesion. Amazingly, the PF coupled with sprayed $\\mathrm{SiO}_{2}$ coatings and the MPA had a low CAH of less than $2^{\\circ}$ . From a thermodynamic point of view, eliminating a liquid from its solid substrate requires the energy to overcome the adhesion.32 The basic relation between the work of adhesion and surface wettability is given by the Dupre–Yong equation,33 \n\n$$\nW_{\\mathrm{e}}=\\gamma_{\\mathrm{lv}}(1+\\cos\\theta_{\\mathrm{c}})\n$$ \n\nwhere $W_{\\mathrm{e}}$ is the work of adhesion at the equilibrium state and $\\gamma_{\\mathrm{lv}}$ is the surface tension of the liquid–vapor interfaces. At a large static CA, it requires a small amount of work to remove droplets. When the $\\mathrm{SiO}_{2}$ coatings were applied on the top of the MPA using the spraying technology, their morphology changed dramatically as shown in Fig. 2b. Specically, the pillars retained their microscale geometrical characteristics and also exhibited nanometer roughness due to the presence of the $\\mathrm{SiO}_{2}$ particles. Moreover, the increase in the CA of the $\\mathrm{SiO}_{2}$ -sprayed MPA was followed by a noticeable decrease in the water adhesion. Since the water drops roll off easily on the patterned surface, we can assume that the water drops stay on the top of the MPA without penetrating the gap between the neighboring pillars. Thus, by simply spraying $\\mathrm{SiO}_{2}$ on the PF with the MPA, we created “non-sticky” superhydrophobic surfaces (see ESI Video S1†). The very low water adhesion is due to the $\\mathrm{SiO}_{2}$ coatings in combination with the geometrical features of the rough surface, which further veried the superhydrophobic antifogging effect of both adding $\\mathrm{SiO}_{2}$ and the creation of the MPA on the PDMS surface. In summary, on one hand, a foundation of hydrophobic $\\mathrm{SiO}_{2}$ nanometer coatings can achieve the superhydrophobic PF chemically. On the other hand, the MPA further amplied the hydrophobic effect to realize the superhydrophobic effect ( $\\mathbf{\\tilde{CA}}=158^{\\circ}$ and $\\mathbf{CAH}=2^{\\circ}$ ) physically, which played a crucial role in achieving the antifogging property. \n\nThe water droplet bounce behaviors on the as-prepared PF were recorded with the help of a high-speed video camera when a $15.6~\\upmu\\mathrm{L}$ water droplet was dropped from a height of $54.8~\\mathrm{mm}$ (see ESI Video $^{S2\\dagger}$ ). The dropping height was determined by the maximum height avoiding droplet fragmentation upon impact with the surface, ensuring maximum droplet momentum. This droplet volume ${\\mathit{\\Omega}}({\\approx}16\\ \\upmu\\mathrm{L})$ was found to be optimum as the droplet could be replicated easily and fell under its own weight when dropped from a 23 gauge dispensing tip. As shown in Fig. 4, the water droplet deformed quickly aer contact with the as-prepared PF. The initial impacting velocity of the droplet was $0.94~\\mathrm{ms}^{-1}$ . At $3.1\\mathrm{ms}$ , the spherical water droplet reached a disclike form. Then, the water drop began to bounce twice and nally completely separated from surface of the as-prepared PF within $86.8~\\mathrm{ms}$ , which further illustrates the excellent superhydrophobic and low adhesion properties. \n\nFurthermore, since fogging results in a certain degree of transmittance loss, we quantied the response of the at PF, PF with the MPA and PF coupled with sprayed $\\mathrm{SiO}_{2}$ coatings and the MPA to fogging at regular intervals $\\left(T_{\\mathrm{t}}\\right)$ until the original transmittance $\\left(T_{\\mathrm{max}}\\right)$ was restored. In order to characterize the antifogging recovery property, the variation trends of the timelapse transmittance measurements of the three PFs were performed aer being sprayed by the generated fog. For this purpose, we built a spray simulation system to characterize their antifogging properties.34 The PF was xed by a clip which was adjusted to be perpendicular to the light beam. As shown in Fig. 5a, recovery from fogging was much faster for the PF coupled with sprayed $\\mathrm{SiO}_{2}$ coatings and the MPA, with $T_{\\mathrm{max}}/T_{t}$ reaching a plateau in far less time than the others. It was conrmed that the PF coupled with sprayed $\\mathrm{SiO}_{2}$ coating and the MPA possesses a superior ability for antifogging recovery, especially in wet and humid environments.35 \n\nIn order to clarify the reasons that the PF coupled with sprayed $\\mathrm{SiO}_{2}$ coating and the MPA possessed the superhydrophobic-antifogging function we investigated the chemical composition of the as-prepared PF surface. Fig. 5b shows the EDS spectra of the as-prepared PF and the results indicated that the fabricated PF is composed of three elements, carbon (C), silicon (Si) and oxygen (O). FTIR spectra of the commercial $\\mathrm{SiO}_{2}$ coating agent, the PF with the MPA and the PF coupled with sprayed $\\mathrm{SiO}_{2}$ coatings and the MPA were obtained. The FTIR spectrum of the commercial $\\mathrm{SiO}_{2}$ coating agent is shown in Fig. 5c. The peak at $810~\\mathrm{{cm}^{-1}}$ is due to Si–O–Si symmetric stretching, and the Si–O–Si asymmetric vibration is at $1082~\\mathrm{cm}^{-1}$ . The peaks at 1264 and $2960~\\mathrm{cm}^{-1}$ correspond to the symmetric bending vibration of $\\mathbf{Si-CH}_{3}$ and symmetric stretching vibration of $\\mathbf{Si-CH}_{3}$ , respectively. The peaks at 850 and $1405~\\mathrm{cm}^{-1}$ are due to the Si–C bending and $\\mathrm{si-C}$ stretching vibrations, respectively. The $\\mathbf{Si-CH}_{2}$ stretching band is at $2850~\\mathrm{cm}^{-1}$ and the peaks at 1389 and $1460~\\mathrm{cm}^{-1}$ are due to the bending vibration of $\\mathbf{Si-CH}_{2}$ .36 The FTIR spectrum of the PF with the MPA and the PF coupled with sprayed $\\mathrm{SiO}_{2}$ coatings and the MPA is shown in Fig. 5d. The peak at 1089 is attributed to the Si–O–Si stretching vibration. The peaks at around 1263 and $803~\\mathrm{cm}^{-1}$ are assigned to the Si–C groups. Other characteristic peaks in the spectrum are assigned to the –CH, $\\mathbf{-CH}_{2}$ and $\\mathbf{-CH}_{3}$ groups of the polymer backbone $2964~\\mathrm{cm}^{-1},$ $2904~\\mathrm{cm}^{-1}$ and $1415~\\mathrm{cm}^{-1}$ , respectively). It could be observed that the FTIR spectrum of the modied PF is consistent with the FTIR spectrum of the untreated PF.37 The above results not only suggest the commercial $\\mathrm{SiO}_{2}$ coating agent without any impurities, but also the as-prepared PF, was enriched with extreme superhydrophobicity and low adhesion, due to the hydrophobic functional groups $\\mathbf{\\bar{\\Pi}}_{\\mathbf{-CH}_{2}}$ and $\\begin{array}{r}{-\\mathbf{C}\\mathbf{H}_{3}\\overline{{.}}}\\end{array}$ ) of the $\\mathrm{SiO}_{2}$ coating. \n\n \nFig. 4 Bounce dynamics of a water droplet impacting with the PF coupled with sprayed $\\mathsf{S i O}_{2}$ coatings and the MPA surface. \n\nTo examine the antifogging property more intuitively, a 3D ultra-depth stereoscopic microscope was used to observe the micro-dynamic behaviour of fog drops on the PF coupled with sprayed $\\mathrm{SiO}_{2}$ coatings and the MPA surface (see ESI Video ${\\bf S}3\\dagger$ ). First, many individual fog drops with a spherical appearance were occurring on the top of the micropillars. As time went on, we found some tiny fog drops began to merge with each other and form new fog drops. As shown in Fig. 6, fog drops A–E were growing smoothly $(t=20~\\mathrm{s})$ ). Subsequently, fog drops B and C coalesced into larger fog drop F $\\left(t=30~\\mathrm{s}\\right)$ , fog drops D and E coalesced into larger fog drop H $\\left(t=45~s\\right)$ and fog drops A and F coalesced into larger droplet I $\\left(t=55s\\right)$ . Then, fog drops H and I merged with fog drop G and formed fog drop J $(t=90\\ s)$ . This indicated that the condensed fog drops can be in Cassie’s state. We theorised that a de-wetting transition phenomenon may occur on the surface,38 then the released surface energy can propel the fog drop jumping or self-removal from the surface.39,40 Furthermore, when this ying fog drop touched another constrained fog drop, a transition would again be stimulated. Due to the occurrence of the de-wetting transitions and the self-removal phenomenon, the MPA can get dry and the fog drops can drop from the PF by means of the low surface adhesion. \n\nIn order to verify our hypothesis about antifogging behaviour on the PF coupled with sprayed $\\mathrm{SiO}_{2}$ coatings and the MPA surface, the macro-dynamic process of fog drop movement was recorded using a 3D ultra-depth stereoscopic microscope (see ESI Video ${\\bf S4\\dagger}$ ). As shown in Fig. 7a, the fog spray was applied to the surfaces, some tiny fog drops initially condensed on the surface and subsequently the fog drops became gradually larger. As time went on, we amazingly found the same phenomenon as Fig. 6, that some tiny fog drops began to merge with each other and form larger fog drops (see the same color circles from $t=90\\mathrm{~s~}$ to $t=196\\mathrm{~s~}$ ). In addition, when the fog drops grew to a certain size, the same phenomenon occurred as in ESI Video $^{85,\\dagger}$ that these fog drops began to roll off suddenly. It is interesting that this roll-off performance removed some circumjacent tiny fog drops, sweeping the surface clean and keeping the area dry (see purple circle at $t=236\\mathrm{~s~}$ ). This is consistent with our previous conjecture and demonstrated the excellent antifogging property of the as-prepared PF surface. To evaluate the antifogging ability of the PF coupled with sprayed $\\mathrm{SiO}_{2}$ coatings and the MPA surface, we estimated the percentage of dry areas versus time, as shown in Fig. 7b, at $\\sim50\\mathrm{~s~}$ , the percentage was lower, but the percentage increased suddenly aer ${\\sim}200\\ s$ , and the percentage was maintained at ${\\sim}83\\%$ from ${\\sim}250$ to 500 s on the whole. This demonstrated the superior antifogging property of the PF coupled with sprayed $\\mathrm{SiO}_{2}$ coatings and the MPA surface. \n\n \nFig. 5 (a) Antifogging of the three PFs is quantified by performing time-lapse transmittance measurements $(T_{\\mathrm{t}})$ to determine the required time to restore their original optical properties $(T_{\\mathrm{max}})$ . The PF coupled with sprayed $\\mathsf{S i O}_{2}$ coatings and the MPA shows a significantly faster recovery from fogging. (b) Energy-dispersive X-ray spectroscopy (EDS) spectra of the PF coupled sprayed $\\mathsf{S i O}_{2}$ coatings and the MPA. (c) FTIR spectra of the commercial $\\mathsf{S i O}_{2}$ coating agent. (d) FTIR spectra of the PF with the MPA (black) and the PF coupled with sprayed $\\mathsf{S i O}_{2}$ coatings and the MPA (purple). \n\nIn order to further reveal the internal antifogging mechanism of the PF coupled with sprayed $\\mathrm{SiO}_{2}$ coating and the MPA, one possible reasonable explanation for these ndings was that the synergistic effect of the droplets intermolecular attraction, chemical compositions and the MPA was the key factor in realizing the superhydrophobic antifogging property. On one hand, the low surface energy methylated $\\mathbf{-CH}_{3}$ and $\\begin{array}{r}{-\\mathbf{C}\\mathbf{H}_{2}\\dot{\\mathbf{\\upmu}}_{.}}\\end{array}$ ) components resulted from the $\\mathrm{SiO}_{2}$ nanometer coatings, which further increased the PF surface hydrophobicity and dramatically decreased the PF surface adhesion to water droplets. \n\nIndeed, the sliding angle for the water drops occurred for a CAH of less than $2^{\\circ}$ . Since the water drops rolled off easily on the PF surface, we can assume that the water drops stayed on the top of the MPA without penetrating the interpillar areas, and then induced tiny condensed droplets to merge with each other easily until shed from the surface. Moreover, the evaporation rate of fog drops was also improved.41 Physically, the fog drops would remain repulsive to the MPA due to the surface forces having sufficient magnitude to suspend liquid against the downward pull of gravity (or other body forces) (see ESI Videos S6 and ${\\bf57\\dagger}$ ). As a whole, the water molecules were affected by a repulsion force of the material itself $\\left(F_{1}\\right)$ intermolecular attraction $\\left(F_{2}\\right)$ , a repulsion force of micro-pillared arrays $\\left(F_{3}\\right)$ , surface tension $(\\sigma)$ and their own gravity $(G)$ (Fig. 8). \n\nOn the other hand, it is a universal strategy to construct a superhydrophobic surface by creating surface roughness onto a low surface energy material. Interestingly, the $\\mathrm{SiO}_{2}$ -sprayed MPA played a signicant role in amplifying the PF’s intrinsic hydrophobicity, which dramatically increased the surface roughness. Specically, the pillars retained their microscale geometrical characteristics and also exhibited nanometer roughness due to the presence of the $\\mathrm{SiO}_{2}$ coating. The combination of the micro/nano-roughness as well as the wellknown water-repellent chemical properties of the PDMS made the patterned surfaces superhydrophobic. Previous researchers have reported that the relationships between CA and roughness ratio in two different wettability states were quantitatively described as the Wenzel model and the Cassie–Baxter model42 which indicated that the true CA of a at hydrophobic surface would be lower with the increase in surface asperities. The very low water adhesion was due to the inherent property of the $\\mathrm{SiO}_{2}$ coatings in combination with the geometrical features of the MPA. Apparently, it was the hierarchical amplication effect of $\\mathrm{SiO}_{2}$ -sprayed MPA that brought big rewards for the achievement of the superhydrophobic antifogging surface. In addition, with the increase in the hydrophobic specic surface that arose from the $\\mathrm{SiO}_{2}$ -sprayed MPA, the PF surface free energy was obviously reduced. According to energy minimization theory,43 once a droplet coalesces with the adjacent droplets, the released surface energy will overcome droplet adhesion, which may induce the fog drops from a Wenzel state to a Cassie–Baxter state,31 so that coalescing fog droplets can self-remove from PF surfaces. Consequently, the transmittance of the PF coupled with sprayed $\\mathrm{SiO}_{2}$ coatings and the MPA would recover to the initial state. These were exactly consistent with the results of the transmittance spectra. \n\n \nFig. 6 (a) Optical images show the micro-dynamic behaviour of the fog drops movement on the PF coupled with sprayed $\\mathsf{S i O}_{2}$ coatings and the MPA surface. From $t=0$ s to $t=90$ s, as the fog drops (A–E) grow larger gradually $(t=20\\ s)$ , they will merge with each other, fog drops B and C coalesce into larger fog drop F $\\left(t=30\\ s\\right)$ , fog drops D and E coalesce into larger fog drop H $(t=45s$ ) and fog drops A and F coalesce into larger droplet I $\\left(t=55s\\right)$ ). Then, fog drops H and I merge with fog drop G and form fog drop J $(t=90~\\mathsf{s})$ . (b) Time evolution of the diameter of an individual fog drop during the merge process (blue triangles). The inserts correspond to $t=20$ , 30, 45, 55 and $90~\\mathsf{s}.$ (c) Additional details are displayed with the assistance of schematic diagrams. \n\n \nFig. 7 (a) Optical images show the macro-dynamic process of the fog drops movement on the PF coupled with sprayed $\\mathsf{S i O}_{2}$ coatings and the MPA surface. From $t=90$ s to $t=236s$ , with water condensation, some tiny fog drops began to merge with each other and form larger fog drops (the same color circles from $t=90~\\mathrm{s}$ to $t=196\\ s)$ . As the fog drops reach a certain size, the fog drops begin to roll off suddenly and take away some surrounding tiny fog drops (purple circle at $t=236s\\mathrm{,}$ . (b) The percentage of dry areas versus time. At ${\\sim}50\\ s.$ , the percentage is lower, but the percentage increases suddenly after ${\\sim}200\\ s,$ and the percentage was maintained at $\\sim83\\%$ from ${\\sim}250$ to 500 s on the whole. \n\n \nFig. 8 The antifogging behaviors of the PF coupled with sprayed $\\mathsf{S i O}_{2}$ coating and the MPA. Here, $F_{1}$ is the repulsion force of the material itself, $F_{2}$ is the intermolecular attraction, $F_{3}$ is the repulsion force of the micro-pillared arrays, $\\sigma$ is surface tension and $G$ is gravity.",
|
||
"category": " Results and discussion"
|
||
},
|
||
{
|
||
"id": 4,
|
||
"chunk": "# 3. Conclusions \n\nIn summary, an antifogging PDMS, inspired by some typical creatures from nature with superhydrophobic surfaces, was designed and fabricated successfully via traditional UV lithography combined with a so replication and subsequent spray coating technique. First, the dimensional uniformity and quality of the bio-inspired PF was characterized using FESEM. It was conrmed that this bio-inspired PF had a coupling surface structure integrated MPA and functionalized $\\mathrm{SiO}_{2}$ coating. FTIR results indicated that both the functional groups of $\\mathbf{-CH}_{2}$ and $\\mathbf{-CH}_{3}$ existed on the surfaces of the bio-inspired PF samples. \n\nIt not only increased its hydrophobicity dramatically, but also decreased its water adhesion property, ensuring the PF surface achieved superhydrophobic antifogging performance. Meanwhile, a set of optimized models were generated to illustrate the fabrication process. Moreover, the nal antifogging behaviors were also revealed. The antifogging properties of PF coupled with sprayed $\\mathrm{SiO}_{2}$ coating and the MPA were characterized experimentally using a spray simulation system and optical CA measuring devices. The time-lapse transmittance measurements demonstrated that the bio-inspired PF also possessed superior fogging recovery property (less than 13 s). It conrmed the reliable optical performance of this advanced antifogging material in practical outdoor conditions. Furthermore, dynamic antifogging behaviors of the bio-inspired PF coupled with sprayed $\\mathrm{SiO}_{2}$ coatings and the MPA were also observed carefully. It can be conrmed that the bio-inspired PF possesses excellent superhydrophobicity and antifogging behaviours. It is anticipated that the ndings reported here provide direct guidance for the future design of superhydrophobic antifogging materials on polymers and other material substrates, and suggest great potential value for specic antifogging applications, such as solar cell panels and window buildings.",
|
||
"category": " Conclusions"
|
||
},
|
||
{
|
||
"id": 5,
|
||
"chunk": "# 4. Experimental section",
|
||
"category": " Materials and methods"
|
||
},
|
||
{
|
||
"id": 6,
|
||
"chunk": "# 4.1 Materials and chemical reagents \n\nAcetone, anhydrous ethanol and deionized water were purchased from commercial sources in the highest available purity. The negative photoresist SU-8 2005 and its developer were obtained from MicroChem Corp. Glass slides were used for the substrates. The elastomer PDMS Sylgard 184 was purchased from Dow Corning. The $\\mathrm{SiO}_{2}$ coating agent was purchased from Changzhou Nanocoatings Co., Ltd.",
|
||
"category": " Materials and methods"
|
||
},
|
||
{
|
||
"id": 7,
|
||
"chunk": "# 4.2 Preparation of the CMHA \n\nThe procedures were performed as follows: rst, glass slides (approximately $4\\times3~\\mathrm{cm}^{2}]$ were cleaned for $10~\\mathrm{\\min}$ . The substrate was dried at $200^{\\circ}\\mathrm{C}$ for $30\\mathrm{min}$ . Next, SU-8 photoresist was dispensed on a glass slide through a spin-coating program $\\mathrm{500~rpm}$ for $10~\\mathrm{s}$ and $3000~\\mathrm{rpm}$ for 30 s). The substrate was so baked on a level hotplate at $103^{\\circ}\\mathrm{C}$ for $6~\\mathrm{{min}}$ . In addition, the substrate was treated using traditional UV lithography and UV exposure (exposure energy at $158\\mathrm{~mJ~cm}^{-2}$ for 10 s) was performed perpendicularly to a photomask of circle-shaped array patterns. Then a post exposure bake step was carried out at $98~^{\\circ}\\mathbf{C}$ for $5~\\mathrm{{min}}$ to harden the SU-8 layer. The thickness of the resulting lm was approximately $6~{\\upmu\\mathrm{m}}$ . Finally, the substrate was immersed in the developer for $30\\mathrm{~s~}$ . The solution was agitated using a tweezer to obtain the uniform SU-8 CMHA on the glass substrate.",
|
||
"category": " Materials and methods"
|
||
},
|
||
{
|
||
"id": 8,
|
||
"chunk": "# 4.3 Preparation of the micro-pillared array (MPA) \n\nThe CMHA on the glass substrate was used as a master pattern. The procedures were performed as follows: rst, the prepolymer and the curing agent were mixed uniformly and stirred in a glass beaker to synthesize the PDMS. Second, the PDMS was poured over the photoresist layer gently and the assembly was moved into the vacuum chamber for $40~\\mathrm{{min}}$ to remove air bubbles, next it was heated in a drying oven at $80~^{\\circ}\\mathbf{C}$ for $^{1\\mathrm{~h~}}$ to completely cure the PDMS. Last, the solidied PDMS was peeled off from the glass substrate and the MPA was transferred to the PF.",
|
||
"category": " Materials and methods"
|
||
},
|
||
{
|
||
"id": 9,
|
||
"chunk": "# 4.4 Preparation of the sprayed $\\mathbf{SiO}_{2}$ coatings on the MPA \n\nA commercial $\\mathrm{SiO}_{2}$ coating agent was sprayed on top of the asprepared PDMS. A spray coating setup was used to deposit the particles. The distance between the sample and the nozzle head was approximately $15\\ \\mathrm{cm}$ . The samples were baked in a drying oven at $80~^{\\circ}\\mathbf{C}$ for $20\\ \\mathrm{\\min}$ . The spray coating and heating processes were performed twice.",
|
||
"category": " Materials and methods"
|
||
},
|
||
{
|
||
"id": 10,
|
||
"chunk": "# 4.5 Characteristics of the prepared samples \n\nThe uniformity and quality of the fabricated sample was inspected with the help of FESEM (JSM-6700F, JEOL) at an accelerating voltage of $2.0\\mathrm{kV}.$ . The static water CAs of the sample surfaces were estimated with an optical CA measuring device (OCA20 data physics, Germany). The advancing contact angles (ACAs) and receding contact angles (RCAs) were tested using a method in which the droplets were enlarged from 7 to $14\\upmu\\mathrm{L}$ to obtain ACAs and shrunk from 14 to $7~\\upmu\\mathrm{L}$ to obtain RCAs. The CAH was measured by inclining the sample until the droplet start rolling. An XRD sample was xed on the sample stage to keep it even. The commercial $\\mathrm{sio}_{2}$ coating agent was characterized using an X-ray diffractometer (Rigaku). The experiment data were collected from 15 to $60^{\\circ}$ . The compositions and distributions of the main elements in the PF coupled with sprayed $\\mathrm{SiO}_{2}$ coating and the MPA were measured using EDS (OXFORD X-MaxN 150). The chemical bonds of the samples were examined using FTIR spectroscopy (IRAffinity-1S). The transmittance spectra of the three PFs were obtained using a miniature ber-optic spectrometer (Ocean Optics USB 4000) and the light spot size of the incident beam was about $5\\mathrm{mm}$ in diameter. The spectrometer was carefully calibrated with STDWS, a standard white board certied by the National Institute of Metrology of China.",
|
||
"category": " Materials and methods"
|
||
},
|
||
{
|
||
"id": 11,
|
||
"chunk": "# 4.6 Observation of fog drops condensation \n\nThe samples were xed horizontally on the object stage. The spray of a humidier was used to generate condensed fog drops on the sample surface. Aer the surfaces were sprayed, the microscopic and macroscopic dynamic behaviour of the movement of the fog drops on the PF coupled with sprayed $\\mathrm{SiO}_{2}$ coating and the MPA surface were simultaneously observed using the 3D ultra-depth stereoscopic microscope (KEYENCE VHX-5000). The condensation experiments were repeated several times. The laboratory temperature was measured at $29^{\\circ}\\mathbf{C}$ with a relative humidity of $40\\%$ .",
|
||
"category": " Materials and methods"
|
||
},
|
||
{
|
||
"id": 12,
|
||
"chunk": "# 4.7 Spray simulation \n\nThe spray simulation system includes a tungsten-halogen lamp (Ocean Optics LS-1-LL), optical ber, ultrasonic humidier (YADU YC-X100E), optical-collimated bracket, a spectrograph (Ocean Optics USB 4000) and a laptop computer.",
|
||
"category": " Materials and methods"
|
||
},
|
||
{
|
||
"id": 13,
|
||
"chunk": "# Conflicts of interest \n\nThere are no conicts to declare.",
|
||
"category": " Conclusions"
|
||
},
|
||
{
|
||
"id": 14,
|
||
"chunk": "# Acknowledgements \n\nThis work was supported by the National Natural Science Foundation of China (No. 51325501, 51505183 and 51675220), JLU Science and Technology Innovative Research Team (No. 2017TD-04), Joint Construction Project of Jilin University and Jilin Province (No. SF2017-3-4), Graduate Innovation Fund of Jilin University (No. 2017010), Special Funding from China Postdoctoral Science Foundation (No. 2018T110246) and Outstanding Young Talent Fund of Jilin Province (No. 20170520095JH).",
|
||
"category": " Acknowledgements"
|
||
},
|
||
{
|
||
"id": 15,
|
||
"chunk": "# References \n\n1 Q. Zhang, B. Jin, B. Wang, Y. Fu, X. Zhan and F. Chen, Ind. Eng. Chem. Res., 2017, 56, 2754–2763. \n\n2 T. Zhang, Q. Yu, J. Wang and T. Wu, Ind. Eng. Chem. Res., 2018, 57, 4577–4584. \n3 F. Wang and H. Liu, J. Phys. Chem. C, 2018, 122, 3434–3442. \n4 Z. Han, X. Feng, Z. Guo, S. Niu and L. Ren, Adv. Mater., 2018, 30, 1704652. \n5 T. Mouterde, G. Lehoucq, S. Xavier, A. Checco, C. T. Black, A. Rahman, T. Midavaine, C. Clanet and D. Qu´ere´, Nat. Mater., 2017, 16, 658–663. \n6 J. Zhao, A. Meyer, L. Ma and W. Ming, Chem. Commun., 2013, 49, 11764–11766. \n7 F. Xu, X. Li, Y. Li and J. Sun, ACS Appl. Mater. Interfaces, 2017, 9, 27955–27963. \n8 F. Liu, J. Shen, W. Zhou, S. Zhang and L. Wan, RSC Adv., 2017, 7, 15992–15996. \n9 Z. Bai, Y. Hu, S. Yan, W. Shan and C. Wei, RSC Adv., 2017, 7, 1966–1974. \n10 Q. Shang and Y. Zhou, Ceram. Int., 2016, 42, 8706–8712. \n11 M. Wen, L. Wang, M. Zhang, L. Jiang and Y. Zheng, ACS Appl. Mater. Interfaces, 2014, 6, 3963–3968. \n12 R. Wen, S. Xu, D. Zhao, Y.-C. Lee, X. Ma and R. Yang, ACS Appl. Mater. Interfaces, 2017, 9, 44911–44921. \n13 P. Zhang, Y. Maeda, F. Lv, Y. Takata and D. Orejon, ACS Appl. Mater. Interfaces, 2017, 9, 35391–35403. \n14 M. He, Y. Ding, J. Chen and Y. Song, ACS Nano, 2016, 10, 9456–9462. \n15 W. Shi, L. Wang, Z. Guo and Y. Zheng, Adv. Mater. Interfaces, 2015, 2, 1500352. \n16 H. K. Raut, S. S. Dinachali, Y. C. Loke, R. Ganesan, K. K. Ansah-Antwi, A. Gora, E. H. Khoo, V. A. Ganesh, M. S. Saifullah and S. Ramakrishna, ACS Nano, 2015, 9, 1305–1314. \n17 J. Lomga, P. Varshney, D. Nanda, M. Satapathy, S. Mohapatra and A. Kumar, J. Alloys Compd., 2017, 702, 161–170. \n18 L. Ai, J. Zhang, X. Li, X. Zhang, Y. Lu and W. Song, ACS Appl. Mater. Interfaces, 2018, 10, 4993–4999. \n19 S. Das, S. Kumar, S. K. Samal, S. Mohanty and S. K. Nayak, Ind. Eng. Chem. Res., 2018, 57, 2727–2745. \n20 K. H. Oh, H. S. Kang, M. J. Choo, D. H. Jang, D. Lee, D. G. Lee, T. H. Kim, Y. T. Hong, J. K. Park and H. T. Kim, Adv. Mater., 2015, 27, 2974–2980. \n21 I. Hwang, D. Choi, S. Lee, J. H. Seo, K.-H. Kim, I. Yoon and K. Seo, ACS Appl. Mater. Interfaces, 2017, 9, 21276–21282. \n22 M. J. Nine, M. A. Cole, L. Johnson, D. N. Tran and D. Losic, ACS Appl. Mater. Interfaces, 2015, 7, 28482–28493. \n23 J. Yong, F. Chen, Q. Yang, D. Zhang, H. Bian, G. Du, J. Si, X. Meng and X. Hou, Langmuir, 2013, 29, 3274–3279. \n24 J. Yong, F. Chen, Q. Yang, D. Zhang, G. Du, J. Si, F. Yun and X. Hou, J. Phys. Chem. C, 2013, 117, 24907–24912. \n25 J. Yong, Q. Yang, F. Chen, D. Zhang, G. Du, H. Bian, J. Si, F. Yun and X. Hou, Appl. Surf. Sci., 2014, 288, 579–583. \n26 S. Kulinich, S. Farhadi, K. Nose and X. Du, Langmuir, 2010, 27, 25–29. \n27 J. B. Lee, H. R. Gwon, S. H. Lee and M. Cho, Mater. Trans., 2010, 51, 1709–1711. \n28 J. Yeo, M. J. Choi and D. S. Kim, J. Micromech. Microeng., 2010, 20, 025028. \n29 D. M. Sim, M. J. Choi, Y. H. Hur, B. Nam, G. Chae, J. H. Park and Y. S. Jung, Adv. Opt. Mater., 2013, 1, 428–433. \n30 S. S. Chae, K. H. Kim, J. H. Park, K. H. Lee, S. W. Han, J. Y. Oh, H. K. Baik and Y. S. Kim, Adv. Mater. Interfaces, 2016, 3, 1500725. \n31 C. Lv, X. Zhang, F. Niu, F. He and P. Hao, Sci. Rep., 2017, 7, 42752. \n32 Z. Pan, W. Zhang, A. Kowalski and B. Zhao, Langmuir, 2015, 31, 9901–9910. \n33 A. J. Meuler, J. D. Smith, K. K. Varanasi, J. M. Mabry, G. H. McKinley and R. E. Cohen, ACS Appl. Mater. Interfaces, 2010, 2, 3100–3110. \n34 Z. Han, Z. Mu, B. Li, Z. Wang, J. Zhang, S. Niu and L. Ren, ACS Nano, 2016, 10, 8591–8602. \n35 X. Gao, X. Yan, X. Yao, L. Xu, K. Zhang, J. Zhang, B. Yang and L. Jiang, Adv. Mater., 2007, 19, 2213–2217. \n36 X. Zou, C. Tao, K. Yang, F. Yang, H. Lv, L. Yan, H. Yan, Y. Li, Y. Xie and X. Yuan, Appl. Surf. Sci., 2018, 440, 700–711. \n37 Z. Han, B. Li, Z. Mu, M. Yang, S. Niu, J. Zhang and L. Ren, Appl. Surf. Sci., 2015, 355, 290–297. \n38 C. Lv, P. Hao, X. Zhang and F. He, ACS Nano, 2015, 9, 12311– 12319. \n39 M. He, Q. Zhang, X. Zeng, D. Cui, J. Chen, H. Li, J. Wang and Y. Song, Adv. Mater., 2013, 25, 2291–2295. \n40 M. Cao, D. Guo, C. Yu, K. Li, M. Liu and L. Jiang, ACS Appl. Mater. Interfaces, 2015, 8, 3615–3623. \n41 G. McHale, S. Aqil, N. Shirtcliffe, M. Newton and H. Y. Erbil, Langmuir, 2005, 21, 11053–11060. \n42 B. He, N. A. Patankar and J. Lee, Langmuir, 2003, 19, 4999– 5003. \n43 R. Wen, Z. Lan, B. Peng, W. Xu, R. Yang and X. Ma, ACS Appl. Mater. Interfaces, 2017, 9, 13770–13777.",
|
||
"category": " References"
|
||
}
|
||
] |